Anyone who has tried to get rid of mosquitoes knows the problem. You spray, the surface gets wet, and an hour later the flying ones are back. Fog works differently. It stays in the air, slips into corners and gets to spots no nozzle can reach. That’s the main reason thermal handy fogging machine keeps gaining ground in pest control.
The SSE 450 Handy Thermal Fogging Machine from Sai Shree Enterprises is made in India for exactly this job. Inside, a hot coil turns diesel and pest control chemicals into a heavy white cloud. In this post I’ll go through how it works, where it’s useful, how to get it running, and the one habit that keeps it alive for years.
Where Can You Use This Machine?
It’s light enough to carry on a belt, yet one unit still covers around 15,000 sq ft of open ground. Here is where it works well:
• Bungalows, colonies and housing societies
• Schools, colleges and hospitals
• Clubs and community spaces
• Sheds, stables and poultry farms
• Farms and gardens
Farmers, gardeners and professional mosquito control workers use it the most, mainly for wide open areas.
How the SSE 450 Thermal Handy Fogging Machine Works
Think of it as a gas burner heating a metal coil. You pump diesel with the chemical in it through that coil. The hot coil does the real work. The liquid hits it, breaks into super small drops and shoots out the front as fog. Those drops hardly weigh anything, so they don’t drop to the floor. Like incense smoke in a room, they just hang there and slowly drift into every corner.
Step-by-Step Way to Start Thermal Handy Fogging Machine
1. Fill the tank with diesel: Take the white tank off the body and fill it, or pour in through the small cap on top. Either way, use a funnel. It saves you a messy spill.
2. Add the chemical: Pour in Deltamethrin 1.25% ULV. Don’t guess the quantity, Use the quantity your supplier recommends.
3. Fit the gas cylinder: It goes at the back. You’ll see a small gap on the cylinder’s edge. Match it with the raised part on the black holder and twist slowly until it locks in.
4. Open the gas: Turn the black round knob anti-clockwise. A light hiss and a whiff of gas near the front burner tells you it’s flowing.
5. Light the burner: Bring the lighter close to the coil, behind the Coil Protection Sheet at the front, and light it.
6. Wait a bit: Give it 10 to 15 seconds. The coil needs that time to heat up.
7. Start fogging: Press the manual pump under your fingers. Diesel and chemicals run through the hot coil and come out as thick fog.
The Step Most People Skip: Cleaning the Coil
This one habit keeps your Thermal Handy Fogging Machine working for years.
Roughly 15 seconds before you’re done, shut the gas valve at the back. The burner stops heating. Keep pumping after that until only clear diesel comes out, which washes the coil from the inside.
Skip it, and the fog left in the coil cools down and turns to carbon. It sticks hard and blocks the passage. Once it sets, it’s tough to get out, and most of the time the coil needs replacing. That’s money you didn’t have to spend.
Flush after every use. Do the same if the machine lights up but no fog comes out.
Safety and Good Habits
• Don’t touch the front coil guard while the machine is hot.
• Follow the same order of steps every time.
• Only diesel goes in the tank, nothing else.
• Measure the chemical the way your supplier says.
• Keep the gas cylinder somewhere cool and dry afterwards.
• End every session with the coil flush.
Conclusion
The SSE 450 Thermal Handy Fogging machine from Sai Shree Enterprises is easy to run and easy to carry, and it does a solid job on large open areas. When this machine gives trouble, the reason is usually a dirty coil. Flush it with diesel every time, follow the steps in order, stay careful around the hot parts, and you won’t need to worry about it for a long time.
FAQs
1. What is the SSE 450 Handy thermal Fogging machine used for?
It produces a dense white fog for mosquito and flying pest control. Farmers, gardeners and mosquito control workers use it across open areas such as farms, housing societies, schools, hospitals, sheds, stables and poultry farms.
2. How much area can one machine cover?
One unit can cover around 15,000 sq ft of open ground.
3. Why is thermal fog better than a normal liquid spray?
Fog is made of tiny droplets that float and spread on their own. It drifts into small corners that a nozzle spray cannot reach.
4. Are spare parts available for the SSE 450 Thermal Fogging Machine?
Yes, we provide spare parts for the SSE 450 Shoulder Mount Thermal Fogging Machine. You can contact us directly to enquire about specific machine components and replacement parts.
5. Does Sai Shree Enterprises provide after-sales service and support?
Yes, we provide after-sales support and assistance for the SSE 450 Thermal Fogging Machine. Our team can help customers with product-related queries, maintenance guidance, and service-related enquiries.